current position:home page>Products>Test Instrument>Uniblitz>

Uniblitz VMM-D3 Three-Channel Shutter Driver

Updated:2024-07-24

Brand: Uniblitz
Model: VMM-D3
Description: The Uniblitz VMM-D3 is a three-channel shutter driver capable of independently controlling up to three shutters. This compact design puts three complete, individual shutter drivers in a single, stream
Data download

Feedback
WeChat

QQ

Online Service

Product Details

Uniblitz VMM-D3 Three-Channel Shutter Driver Description：

Product Manual Datasheet

The Uniblitz VMM-D3 is a three-channel shutter driver capable of independently controlling up to three shutters. This compact design puts three complete, individual shutter drivers in a single, streamlined package. Active high-level logic inputs allow fully independent shutter control. A single input will activate all channels simultaneously, and a single output is available to monitor when all shutter synchronization system circuits are active. Three active low-level logic outputs monitor the status of each synchronization system output. An addressable RS232-C serial input is also available to control these inputs via a computer serial port, allowing up to eight VMM-D3 units and up to 24 individual shutters to be controlled from a single computer serial port.

Specifications

System Characteristics
Repeat Exposure	Min 50 msec between exposure for 25mm or smaller aperture shutters
	Min 120 msec for 35mm and larger aperture shutters
Shutter Drive	Continuously variable frequency of exposures from DC to the shutter in operation
	Maximum rate detated by 75% when more than one channel in operation
All Inputs	Input Impedance – 4.7K Ohms
Input Control	Active-High
Terminal Block	TTL Compatible
All Outputs	Source Impedance – 1K
Output Control	Active-Low
Terminal Block	TTL Compatible
General	Size (HWD) 2.63 x 5.35 x 8.18 inches (67.0 x 136.0 x 207.9 mm)
	Weight 4.5 lbs (2.02kg)
	Power 115/230 VAC, 50-60 Hz

Front Panel Layout

Front Panel
Shutter Fuse (1)	5 x 20mm,0.6A, “T” time-lag fuse to protect that shutter output-one for each channel.
N.O/N.C Switch (2)	The position of the key switch determines shutter status BEFORE a trigger signal is received by the VMM-D3-one for each channel.
Sync. Active LED(3)	A green LED indicator that indicates status of Solid State Synchronization output-one for each channel.
Driver Active LED (4)	A red LED that indicates when the internal shutter driver circuit input has an active signal present- one for each channel.
RS-232C Input (5)	DB-9 female connector provides access to the VMM-D3 RS-232C interface.
Address Select Switch-SW1 (6)	Selects the active RS-232C address of the unit.
Power Indicator (7)	A red LED indicates that power is applied to the unit.

Rear Panel Layout

Rear Panel
AC Input Module (1)	AC input via IEC male receptical for AC line cord (supplied). Additional functions are described on page(s) 9-1, 15 and page 32 in the VMM-D3/D4 user manual.
Output Control (2)	Provides Electronic Sync. signal output from each shutter channel. Output indicates state of shutter’s Electronic Sync., if shutter is so equipped. One output for each channel. See terminal strip layout in VMM-D3/D4 User Manual page(s) 15-19. Active Low outputs. Output Terminal #5 – Active Low when all Sync. outputs go low.
Input Control (3)	Provides Active High control for each channel. Input TTL high – shutter open, input TTL low – shutter close. Terminal #5 – Active High, input TTL high – all shutters open, input TTL low – all shutters close. See terminal strip layout in VMM-D3/D4 User Manual page(s)15-19.
LO/HI Select Slide Switch (4)	“HI” position allows the selection of appropriate pulse energy for 35 mm and larger shutters.“LO” Position for shutters 25 mm and smaller aperture. One for each channel. Channel #4 slide switch provides no function in the VMM-D4.
Shutter Output (5) Channel #1-#3	Provides connection to shutter used via 7-pin female WirePro™ connector. One for each channel. Channel #4 not operational in the VMM-D3.